Page 1 of 2

counter shaft gear spacer

PostPosted: Tue Nov 30, 2021 5:49 pm
by blewandoski
just started working on 52 K. Missing a few parts. Right now looking for the counter shaft gear spacer (35809-52)
cant seem to find any. Does anyone have the spec's for that part? Or can I sub the gear with a 56 year one (35809-56) I can find plenty of those

Re: counter shaft gear spacer

PostPosted: Tue Nov 30, 2021 11:54 pm
by JerrryR
I don't believe the 35809-52 & the 35809-58 are interchangeable. The ID of the 35809-58 spacer is quite a bit larger than the -52 spacer and the widths are different. I do have one I would loan if you need to have one made.

35809-52 & 58.jpg
35809-52 & 58.jpg (180.83 KiB) Viewed 5834 times

Re: counter shaft gear spacer

PostPosted: Wed Dec 01, 2021 4:08 pm
by blewandoski
thanx for loan offer Jerry. I do know a gear head who can make one but I think a few pictures using a micrometer would work just as well...and saves on the shipping cost ;)

Re: counter shaft gear spacer

PostPosted: Wed Dec 01, 2021 6:00 pm
by 55panman
Yes Jerry, ID, OD and thickness would be quite handy for this spacer as I believe I need one also. Thanks, Ron

Re: counter shaft gear spacer

PostPosted: Wed Dec 01, 2021 11:55 pm
by JerrryR
Hi Ron and Blewandowski, My first post shows most of the dimensions but may not have been noticed since the picture waas large and you needed to scroll to the right to see the dimensions. In going back and looking I realized I was not consistent with terms used with the -52 & -58 spacers. I redid the image, shrunk it and am reposting it here along with pictures of the measurements being taken. I will use two post since I can only do 3 per post. Let me know if you need additional information or want to borrow the part. Good luck, JerryR

35809-52 & 58.jpg
35809-52 & 58.jpg (222.7 KiB) Viewed 5730 times


35809-52, 1.jpg
35809-52, 1.jpg (218.68 KiB) Viewed 5730 times


35809-52, 2.jpg
35809-52, 2.jpg (225.01 KiB) Viewed 5730 times

Re: counter shaft gear spacer

PostPosted: Thu Dec 02, 2021 12:00 am
by JerrryR
35809-52, 3.jpg
35809-52, 3.jpg (211.36 KiB) Viewed 5728 times


35809-52, 4.jpg
35809-52, 4.jpg (192.34 KiB) Viewed 5728 times


35809-52, 5.jpg
35809-52, 5.jpg (201.88 KiB) Viewed 5728 times

Re: counter shaft gear spacer

PostPosted: Fri Dec 03, 2021 11:05 am
by blewandoski
thanx again Jerry...that is just what I needed

Re: counter shaft gear spacer

PostPosted: Thu Jan 13, 2022 3:49 pm
by blewandoski
last question what type of steel is the spacer made out of?

Re: counter shaft gear spacer

PostPosted: Thu Jan 13, 2022 4:54 pm
by JerrryR
That question is above my pay grade. This might be the reason I need to send it to you unless someone else knows.

Re: counter shaft gear spacer

PostPosted: Thu Jan 13, 2022 8:19 pm
by dlxl66elxl
I may have one available, PM me. Dave